This is an old revision of the document!
- 152Eu source sheet z2707-1.pdf
validate: Channels which triggered get written
TTCS: All 40 channels of a triggering crystal get written
in Run directory, file Setpoints: CryG_CS_BRE is status of baseline restorer
| date | directory | run | Description |
|---|---|---|---|
| 6/1/12 | data1b/MSUMay2012 | 37 | 60Co validate |
| 38 | 60Co TTCS | ||
| 46 | 152Eu+60Co, 4kHz/xtal, mode 3 | ||
| 50 | 56Co, Mode 2+3, 1.5Mb/s, dt 92% | ||
| 55 | 56Co, mode 2,3 | ||
| 56 | 56Co, mode 2 | ||
| 57 | 56Co, mode 2+3 | ||
| 58 | 56Co, mode 3, TTCS | ||
| 59 | 56Co, mode 3, validate, trace 2us | ||
| 60 | 56Co, mode 3, validate, trace 0.2us | ||
| 61 | 60Co 10uCi, mode 3, validate, trace 0.2us | ||
| 62 | 60Co, mode 3, validate, trace 2us | ||
| 63 | 60Co, mode 3, TTCS | ||
| 64 | 60Co, mode 2+3 | ||
| 65 | 60Co, mode 2 | ||
| 66 | 152Eu, mode 2 | ||
| 67 | 152Eu, mode 2+3 | ||
| 68 | 152Eu, mode 3, TTCS | ||
| 69 | 152Eu, mode 3, validate, 2us | ||
| 70 | 152Eu, mode 3, validate, 0.2us | ||
| 71 | 226Ra, mode 3, validate, 0.2us | ||
| 72 | 226Ra, mode 3, validate, 2us traces | ||
| 73 | 226Ra, mode 3, TTCS | ||
| 74 | 226Ra, mode 3 | ||
| 75 | 226Ra, mode 2 | ||
| 6/4/12 | data1b/MSUMay2012 | 84 | calibration works, low rate 60Co, mode 2+3 |
| 85 | low rate 60Co, 2+3 | ||
| 87 | 226Ra, mode 3 validate, 2us traces | ||
| 89 | 226Ra, mode 3 validate, 2us traces | ||
| 92 | 226Ra, mode 3 validate, 2us traces | ||
| 94 | 226Ra, mode 3 validate, 2us traces | ||
| 101 | switched to Gretina+S800, TTCS, mode 2+3 | ||
| 102 | 60Co mode 2+3 | ||
| 105 | 60Co, downscaler 10, crystal 5000Mb/sec | ||
| 107 | 60Co, d/s 5 | ||
| 110 | 60Co, d/s 3 | ||
| data1a/MSUJune2012 | 7 | 60Co, d/s 1, 8000Mb/sec, 18% DT | |
| 6/5/12 | data1a/MSUJune2012 | 10 | 5Mev range in mode 2+3, 60Co weak, d/s 10 |
| 12 | 5MeV range in mode 2+3, 152Eu at center, d/s 10, BLR off | ||
| 13 | 5MeV, mode 2+3, 152Eu center, d/s 5, BLR off | ||
| 14 | mode 3 validate, 0.2us trace, 152Eu center, d/s 10, BLR off | ||
| 15 | mode 3 validate, 0.2us trace, 152Eu center, d/s 10, BLR off, HEMIs closed! | ||
| 16 | mode 2+3, 152Eu center, d/s 10, BLR off, HEMIs closed! | ||
| 17 | mode 2+3, 60Co (weak) center, d/s 10, BLR off, HEMIs closed! | ||
| 23 | mode 3 validate, 0.2us, 60Co (weak) center, d/s 10, BLR off, HEMIs closed! | ||
| 24 | mode 3 validate, 0.2us, 60Co (weak) center, d/s 10, BLR off, HEMIs open! | ||
| 25 | mode 2+3, 60Co (weak) center, d/s 10, BLR off, HEMIs open! | ||
| 27 | mode 2+3, no source, d/s 1, BLR off, HEMIs closed! | ||
| 6/6/12 | data1a/MSUJune2012 | 28 | mode 2+3, no source, d/s 1, BLR off, HEMIs open! |
| FROM HERE ON S800 SYNCHRONIZATION SET UP WRONG (most likely) | |||
| 59 | mode 3 TTCS + LaBr, coinc or Gretina ds 50 or LaBr ds 20, most likely S800 did run with internal clock since then → no 'obvious' correlation | ||
| 60 | mode 3 TTCS + LaBr, coinc or Gretina ds 50 or LaBr ds 20 | ||
| 61 | mode 3 TTCS + LaBr, coinc or Gretina ds 50 or LaBr ds 20 | ||
| 62 | mode 3 TTCS + LaBr, coinc or Gretina ds 50 or LaBr ds 20 | ||
| 63 | mode 3 TTCS + LaBr, coinc or Gretina ds 50 or LaBr ds 20 | ||
| 65 | mode 3 TTCS + LaBr, coinc or Gretina ds 50 or LaBr ds 20 | ||
| 6/7/12 | data1a/MSUJune2012 | 67 | mode 3 TTCS + LaBr, coinc or Gretina ds 50 or LaBr ds 20 |
| 69 | mode 3 TTCS + LaBr, coinc or Gretina ds 50 or LaBr ds 20, fill during Run | ||
| 70 | mode 3 TTCS + LaBr, coinc or Gretina ds 50 or LaBr ds 20 | ||
| 71 | mode 3 TTCS + LaBr, coinc or Gretina ds 50 or LaBr ds 20 | ||
| 72 | mode 3 TTCS + LaBr, coinc or Gretina ds 50 or LaBr ds 20 | ||
| 6/8/12 | data1a/MSUJune2012 | 73 | mode 3 TTCS + LaBr, coinc or Gretina ds 50 or LaBr ds 20 |
| 108 | mode 2only Decomp 1-28, sendRaw 29 (TTCS) for LaBr, or Gretina | ||
| 110 | mode 2only Decomp 1-28, sendRaw 29 (TTCS) for LaBr, coinc or Gretina ds 50 or LaBr ds 20 | ||
| HERE WE SET THE S800 SYNCHRONIZATION CHECK BUTTON PROPERLY | |||
| 114 | mode 3 TTCS + LaBr, coinc or Gretina ds 50 or LaBr ds 20 |
