task:scm_off
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| task:scm_off [2025/09/25 01:48] – look | task:scm_off [2025/10/01 00:46] (current) – look | ||
|---|---|---|---|
| Line 11: | Line 11: | ||
| ==== LINAC Solenoids ==== | ==== LINAC Solenoids ==== | ||
| - | **Turn | + | **Turn |
| * Click the lead flow on button for the desired linac segment | * Click the lead flow on button for the desired linac segment | ||
| * Wait for all lead flow LEDs to turn green | * Wait for all lead flow LEDs to turn green | ||
| * Click the solenoids on button for the desired segment after confirming that all lead flows are on | * Click the solenoids on button for the desired segment after confirming that all lead flows are on | ||
| * Check that all solenoids and correctors have ramped to their proper setpoints | * Check that all solenoids and correctors have ramped to their proper setpoints | ||
| - | **Turn | + | **Turn |
| * Click the solenoids off button for the desired linac segment | * Click the solenoids off button for the desired linac segment | ||
| * Wait for all power supplies in the segment to turn off (power supply LEDs should no longer be green) | * Wait for all power supplies in the segment to turn off (power supply LEDs should no longer be green) | ||
| Line 22: | Line 22: | ||
| * Check that all lead flow LEDs for the segment are no longer green | * Check that all lead flow LEDs for the segment are no longer green | ||
| ==== FS2 Dipoles ==== | ==== FS2 Dipoles ==== | ||
| - | **Turn | + | **Turn |
| * Click the two 'LD Valve ON' buttons for the dipoles | * Click the two 'LD Valve ON' buttons for the dipoles | ||
| * Once both of the lead flow power supply LEDs are green and the LFV state message box reads 'LFV ON' for a dipole, click the ' | * Once both of the lead flow power supply LEDs are green and the LFV state message box reads 'LFV ON' for a dipole, click the ' | ||
| * Check that the dipole power supply has ramped to the correct setpoint after the dipole state message box reads ' | * Check that the dipole power supply has ramped to the correct setpoint after the dipole state message box reads ' | ||
| - | **Turn | + | **Turn |
| * Click the 'FS2 SCD# OFF' button for the desired dipole | * Click the 'FS2 SCD# OFF' button for the desired dipole | ||
| * Confirm that the power supply and lead flow LEDs are no longer green after the ramp down | * Confirm that the power supply and lead flow LEDs are no longer green after the ramp down | ||
| Line 32: | Line 32: | ||
| ==== VPS Magnets ==== | ==== VPS Magnets ==== | ||
| + | **Turn On** | ||
| + | * At the bottom of the 'VPS Magnets' | ||
| + | * Confirm that all flow controller power supply LEDs are green | ||
| + | * Click the 'All On' button for the magnet power supplies | ||
| + | * Confirm that all power supply LEDs are green and have ramped to their appropriate setpoints | ||
| + | **Turn Off** | ||
| + | * At the bottom of the 'VPS Magnets' | ||
| + | * Wait for the magnet power supplies to ramp down | ||
| + | * The ramp down will have finished when the readback for the current stops changing | ||
| + | * Click the 'All Off' button for the magnet power supplies | ||
| + | * Confirm that all magnet power supply LEDs are no longer green | ||
| + | * Click the 'All Off' button for the lead flows | ||
| + | * Confirm that all lead flow power supply LEDs are no longer green | ||
| ==== ARIS Magnets ==== | ==== ARIS Magnets ==== | ||
| ===== EXP ===== | ===== EXP ===== | ||
task/scm_off.1758779323.txt.gz · Last modified: 2025/09/25 01:48 by look