FRIB Operators

User Tools

Site Tools

Trace: • Setting the attenuator threshold interlock • Monitoring Target IR Camera • Limiting Primary Beam Power • FSEE Startup and Shutdown Procedure • PDT
task:open_close_target_area

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
task:open_close_target_area [2025/05/08 10:23] – paintertask:open_close_target_area [2025/08/21 12:32] (current) – ryans
Line 3: Line 3:
 == Open ==  == Open == 
   - Turn the Beam/Chopper off   - Turn the Beam/Chopper off
-  - On the Main Magnets page, turn Dipole D5578 off on BBS/FFS tab; this will take a moment to ramp down to 0 A. +  - On the [[pages:mag_main|Main Magnets]] page, turn Dipole D5578 off on BBS/FFS tab; this will take a moment to ramp down to 0 A. 
-  - On the MPS Operator page, turn E-Bends off. +  - On the [[pages:mps_op|MPS Operator]] page, turn E-Bends off.
   - On the PPS rack, turn the Linac ACS key to Power Permit.   - On the PPS rack, turn the Linac ACS key to Power Permit.
   - On the PPS rack, turn the key for Target RSS Ready For Beam to Off.    - On the PPS rack, turn the key for Target RSS Ready For Beam to Off. 
Line 18: Line 18:
   - Ensure you are in required machine mode for beam.   - Ensure you are in required machine mode for beam.
   - Turn the Linac ACS key back to Beam Permit.   - Turn the Linac ACS key back to Beam Permit.
-  - On the Main Magnets page, cycle the D5578 dipole to 90 A on the BBS/FFS tab:+  - On the [[pages:mag_main|Main Magnets]] page, cycle the D5578 dipole to 90 A on the BBS/FFS tab:
       - Copy the current setpoint value.        - Copy the current setpoint value. 
       - Turn on D5578 dipole (this will take a few seconds to go green).       - Turn on D5578 dipole (this will take a few seconds to go green).
Line 24: Line 24:
       - When done ramping to 90 A, paste the original setpoint value.       - When done ramping to 90 A, paste the original setpoint value.
       - Wait for dipole to ramp to original value.       - Wait for dipole to ramp to original value.
-  - On the MPS Operator page, turn the E-Bends on. +  - On the [[pages:mps_op|MPS Operator]] page, turn the E-Bends on. 
-  - On the Main Magnets page check that the E-Bends setpoint and readback values match on the V-LEBT tab. +  - On the [[pages:mag_main|Main Magnets]] page check that the E-Bends setpoint and readback values match on the V-LEBT tab. 
-  - On the MPS Operator page, set configuration according to MPS Device Configuration Guideline.+  - On the [[pages:mps_op|MPS Operator]] page, set configuration according to MPS Device Configuration Guideline.
   - Check and clear all set MPS devices.    - Check and clear all set MPS devices. 
   - Start the Chopper.   - Start the Chopper.
  
 +====SN==== 
 +*good page, could benefit from some "why's" but I can see that being ideally on another adjacanet page or something
  
 ===== Links ===== ===== Links =====
task/open_close_target_area.1746714221.txt.gz · Last modified: 2025/05/08 10:23 by painter
Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki