Differences

This shows you the differences between two versions of the page.

--- life:what_s_an_accelerator [2025/06/25 20:47] – ryans
+++ life:what_s_an_accelerator [2025/08/07 01:53] (current) – ryans
@@ Line 78: / Line 78: @@
   * We use the __Lithium Stripper Stage Feedback Tool__ in order to counteract this, the stripper stage eludes me somewhat admittedly, but a summary of how we interact with it can be found __here__.
+**Notes**
+  * Maybe add in a pic of the graphs from the litium stripper feedback and explain what is going on/how to identify trips and when it levels out.
+  * Could add in details about the viewers here or start a subsection here about the viewers since you can view the lithium stripper from them.
 ====Sensors and More Alarms====
   * I talked quite a bit about tripping MPS there, as far as the __Lithium Stripper__ goes this will likely be because of the __Beam Current Monitors__ or BCMs. They measure the amount of beam at one point in the beamline and gives units of uA. The ones that trip MPS the most are the __Differential Beam Current Monitors__, which are just two BCMs that compare readings. If a significant amount of beam is lost somehow between those two points then beam trips off. We have poked holes in the beamline from "losing" beam on a bellow so it's something we need to be very careful about. This is covered under MPS as this beam loss really only endangers the machine.
   * Different Differential BCMs are normally named after the region they're monitoring. LS1TRANS is the transmission through LS1, once you're comfortable with the LINAC and its components most of them will make sense, the only exception possibly being the LINACTGT, which measures from the start of the LINAC to the target.
-  * This isn't the only way to detect beam loss, we also have __Neutron Detectors__ which are out go-to's anytime we're worried about beam-born radiation leaking out. These look like big white tupperware cylinders that you can see if you ever walk by N4. Tunnel __Neutron Monitors__ are connected to MPS because if there's a person down in the __Tunnel__, the area where the LINAC is, while beam is running then there's bigger issues.
+  * This isn't the only way to detect beam loss, we also have __Neutron Detectors__ which are our go-to's anytime we're worried about beam-born radiation leaking out. These look like big white tupperware cylinders that you can see if you ever walk by N4. Tunnel __Neutron Monitors__ are connected to MPS because if there's a person down in the __Tunnel__, the area where the LINAC is, while beam is running then there's bigger issues.
   * We also have __X-Ray Monitors__ in the __Tunnel__, but these are to monitor __cavities__, you might remember that cavities within the same cryomodule can "interact" with each other, a lot of this comes down to x-rays. Errant X-rays can prevent cavities from turning on (read more __here__), and aside from that they can tell experts things about the health of the cavities.
@@ Line 88: / Line 91: @@
   * I would say there's three interesting concepts within FS1. If you look at a diagram of it you'll notice 2 (or 3) arms coming off of it. The first of these is the __FRIB Single Event Experiment__ beamline, or the FSEE Beamline for short. You'll notice a __dipole__ that if powered on would continue the beam through the rest of the LINAC, if turned off the beam will continue into the FSEE Beamline.
-  * From here is a second __dipole__, this choice is a bit more complicated however. If the __dipole__ is off then beam will continue into a __Beam Dump__, or often a "BD" for short. __Beam Dumps__ are exactly what they sound like, places to dump beam and no worry too much about it. These are big receptacles made to take beam without irradiating too much outside of it.
+  * From here is a second __dipole__, this choice is a bit more complicated however. If the __dipole__ is off then beam will continue into a __Beam Dump__, or often a "BD" for short. __Beam Dumps__ are exactly what they sound like, places to dump beam and not worry too much about it. These are big receptacles made to take beam without irradiating too much outside of it.
-  * If the __dipole__ is on, then the beam gets sent towards the FSEE Experiment. This is a topic with a lot of depth to it, but in short we use this for some outside entities that would like to test how their stuff works when experiencing low level radiation like this. often mimicking the increased radiation present in space or high atmosphere. Read more about it __here__.
+  * If the __dipole__ is on, then the beam gets sent towards the FSEE Experiment. This is a topic with a lot of depth to it, but in short we use this for some outside entities that would like to test how their stuff works when experiencing low level radiation like this. Often mimicking the increased radiation present in space or high atmosphere. Read more about it __here__.
   * Lastly for FS1, if the first __dipole__ is on and the __FSEE Beamline__ is avoided, there is a second beam dump, or if all four of the dipoles are on, the charge selector.
   * I don't know anything about the charge selector
@@ Line 97: / Line 100: @@
   * Recall however, that the source slits and charge selector have many things between them, notably the __Lithium Stripper__. This would mean that for an unwanted isotope to get past the charge selector, it would have to have 2 ionizations that overlap with the desired isotope at the desired ionization. Many ions are also fully stripped by this point, after the __Lithium Stripper__, making it all the more unlikely that these m/q's line up.
+====Vacuums====
+  *The whole beamline is kept under a pretty extreme vacuum, this is generally anywhere between e-8 Torr to e-12 Torr! There are many devices that we use to accomplish this, but here are a few of the main ones. Note also that a lot of them only work for a specific range of pressures.
+    - **Gate Valves**: Gate Valves are beamline devices that can portion off segments of the beamline any other space we intend to pump down on. Their primary responsibility is to contain any fluctuations in the vacuum pressure and stop them from propagating. There are also **Turbo** Gate Valves, which are distinct in their ability to close very quickly and rather violently, this can be greatly helpful to prevent total vacuum excursions in the case of a leak, but due to their extreme nature have a short shelf life and should be actuated as infrequently as possible.
+    - **Pirani Gauge**: These are measurement devices that work best for higher pressure spaces, you'll often see these reading nominal values of e-4 Torr. Their primary uses are for **roughing**, or pumping down on atmospheric or near atmospheric regions, or for the higher pressure **Insulating Vacuums**, which I'll cover next.
+    - **Roughing Pumps**: Scroll Pumps, Ion Pumps, Roughing Pumps, I'm sure I'm forgetting one, but generically these are pumps that are used for higher pressures, there are differences between them, but I'm no expert and it's all a bit more info than is really necessary for our role. Andy knows a lot about vacuums, feel free to ask him if things are quiet! These pumps reduce pressure, either to a desired point, or to a point where more powerful pumps can take over and further reduce pressure. I believe they stay on even after more powerful pumps are activated.
+    - **Cold Cathode Gauges**: CCG's are like Pirani Gauges, but work for much lower pressures, like those e-12 Torr areas I mentioned earlier. They do tend to turn themselves off when exposed to higher pressures so they don't break, so every now and again one will "trip off" due to those higher pressures despite being a diagnostic, or measurement, device.
+    - **Turbo Pumps**: What CCG's are to Pirani Gauges, Turbo Pumps are to Roughing Pumps. Once the PG's and Roughing Pumps give us a lower pressure environment, the CCG's and Turbo Pumps work to further reduce pressure from ~e-4 to something like e-10. They also can be harmed if they try to operate when pressure is too high, also an interesting thing to note is that for these lower pressures you don't get the outward flow of gas like you'd envision for atmospheric systems. Here the random travel of molecules within the vacuum matters greatly and the pump can't do much until one of them happens to cross its path. Like a cellular pump or a venus fly trap, it becomes a game of waiting, even if not for long.
+  * **Insulating Vacuums** are not vacuums we intend to send beam through, they're as the name suggests, a vacuum to limit the transfer of heat into some protected device. Air is a decent insulator, but an even better insulator is nothing, given that a vacuum is just an attempt at nothing the intent here becomes clear. These are not as great of vacuums as you'd find in the beamline, the marginal increase in insulation does not make up for the increase in complexity and power necessary to run a full turbopump set up, so they mostly stay in the e-4 Torr range. What kind of devices do they insulate? Great Question! Often these are our **Super Conducting Magnets** or **SCMs**. What are they? Well...
+====SCM vs Room Temp Magnets====
+  * **SCMs** not sure I know enough about this, where do i find more imll research
+  * Not all magnets are Super Conducting, a phenomenon that occurs when you make the magnet really really cold, if your professor ever made a cold magnet run around a track like f zero then this is the same concept. This requires cryogenic support to super cool and has a different department to work on. The only time we really need to care about if a magnet is super conducting or not is if something happens to it, then the alarm should tell you if it's superconducting or room temperature.
 ====Rest of LINAC====
 honestly very boring after that.
+====Target====
+  *We made it! The target is made out of something and at higher beam powers we need to spin it to prevent overheating. You may also recognize it from the display, where it should look rainbowy, very cool!
+  *Of the two tasks the involve the target, the easier one is working with Matthias Steiner to measure the thickness of the Target. You can read more about that __here__, as the more interesting aspects are purely documentation and safety.
+  *We can also start or stop the target, nominally it runs at 500 rpm. It must be stopped on occasion, such as when the remote handling group needs to do their work. That process is explained __here__.
+====The End(?)====
+  * I really wish it was, but this isn't even the end of the ftc network. This is a long page and it covers a lot of information, really most of what you need to know regarding the devices in the beamline upto the target. However there is more, which can be found in __What is an Accelerator II__. See you there when you're ready.
+OTHER IDEAS
+   *wedges
+   *dccts
+   *target and ARIS specifics
+   *idk shane 2 add stuff